SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.
QUESTIONS REGARDING THIS DOCUMENT: (412) 772-8512 FAX: (412) 776-0243
TO PLACE A DOCUMENT ORDER; (412) 776-4970 FAX: (412) 776-0790
SAE WEB ADDRESS http://www.sae.org
Copyright 1993 Society of Automotive Engineers, Inc.All rights reserved.
Printed in U.S.A.
SAE J561 Revised JUN93TABLE 1A—METRIC STUD OR SCREW AND HOLE OR SLOT SIZESHole orSlot SizeFor Eyeletor Spade,
AMin 3.2 mm 4.2 mm 5.3 mm 6.3 mm 8.4 mm10.5 mm12.5 mm14.6 mm16.7 mm
Hole orSlot SizeFor Eyeletor Spade,
AMax 3.4 mm 4.4 mm 5.5 mm 6.5 mm 8.6 mm10.7 mm12.9 mm15.0 mm17.1 mm
SAE No.1M2M3M4M5M6M7M8M9M
Metric Stud orScrew SizeNominal
M3M4M5M6M8M10M12M14M16
Metric Stud orScrew Size
Max
3.0 mm 4.0 mm 5.0 mm 6.0 mm 8.0 mm10.0 mm12.0 mm14.0 mm16.0 mm
TABLE 1B—STUD OR SCREW AND HOLE OR SLOT SIZESHole orSlot SizeFor Eyeletor Spade,
AMin0.123 in0.144 in0.170 in0.201 in0.279 in0.342 in0.404 in0.466 in0.528 in
Hole orSlot SizeFor Eyeletor Spade,
AMax0.129 in0.150 in0.176 in0.207 in0.285 in0.348 in0.410 in0.476 in0.538 in
SAE No.
123456789
Stud orScrew SizeNominal
4 6 8 10 1/45/16 3/87/16 1/2
Stud orScrew Size
Max0.112 in0.138 in0.164 in0.190 in0.250 in0.313 in0.375 in0.438 in0.500 in
-2-SAE J561 Revised JUN93FIGURE 1—STRAIGHT-TYPE EYELET AND SNAP-ON EYELET TERMINALS-3-SAE J561 Revised JUN93FIGURE 2—STRAIGHT-TYPE SPADE TERMINALS-4-SAE J561 Revised JUN93FIGURE 3—SIDE-TYPE SPADE TERMINALS-5-SAE J561 Revised JUN93FIGURE 4—SIDE-TYPE EYELET TERMINALS-6-SAE J561 Revised JUN93FIGURE 5—END-TYPE STARTING-CABLE TERMINALS-7-SAE J561 Revised JUN934.4.1NotesMarginal Indicia—The (R) is for the convenience of the user in locating areas where technical revisions havebeen made to the previous issue of the report. If the symbol is next to the report title, it indicates a completerevision of the report.PREPARED BY THE ELECTRICAL DISTRIBUTION SYSTEMS STANDARDS COMMITTEE-8-SAE J561 Revised JUN93Rationale—The changes to SAE J561 include:1.Under Section 3, first sentence, Tables 1a and 1b and Figures 1 through 5 of, was added.2.The document has been revised to comply with SAE Electronic Capture Guidelines. This includesadding Section 2 as the Reference Section and having metric as the primary units. All tables havebeen changed to the metric units as primary.Relationship of SAE Standard to ISO Standard—Not applicable.Application—This SAE Standard covers general requirements and dimensions of various sizes of eyelet andspade type terminals.Reference SectionSAE J163—Low Tension Wiring and Cable Terminals and Splice ClipsDeveloped by the SAE Electrical Distribution Systems Standards Committee
因篇幅问题不能全部显示，请点此查看更多更全内容